Description
CT2N SRM5P relay box for five marine windscreen wipers
The CT2N SRM5P is the electronic switching unit of a wiper control system for five motors. The module receives commands from the dashboard control panel and switches the motor outputs for the selected wiping functions.
This relay box is supplied separately as a replacement part for an existing SRM5P module. The corresponding control panel and connecting cable are not automatically included in the delivery.
Operation within the CT2N wiper system
The SRM5P operates together with a compatible CP4P5 control panel. Control signals are transmitted to the relay box via a CAN bus connection.
In combination with suitable wiper motors, the system supports the following functions:
- Individual motor selection: Each wiper can be switched on and off individually.
- Synchronisation: The wiping movements of multiple active motors are electronically coordinated.
- Continuous wiping speeds: Slow and fast wiping with suitable two-speed motors.
- Intermittent control: Three intermittent settings for two-speed motors and four for single-speed motors.
- Automatic parking function: The motors return to their preset park position after being switched off.
- Dynamic braking: Supports precise stopping of the motors in the park position.
- Wash/wipe programme: Electronic control of a suitable windscreen washer system.
The operation of the synchronisation and parking functions depends on the park switches in the connected motors. These must be electrically compatible with the control system.
Five motor outputs and electrical protection
The SRM5P has five separate motor outputs. Each output supports a maximum load of 12A and has its own self-resetting protection.
If a motor becomes blocked or an electrical overload occurs, the corresponding protection may be activated. The relay box also features reverse polarity protection for the supply voltage.
Electrical specifications:
- Supply voltage range: 10-30V DC
- Nominal onboard voltage: 12/24V DC
- Maximum motor current: 12A per motor
- Internal protection: Self-resetting, 12A per motor
- Standby current consumption at 10V: Less than 70 mA
- Standby current consumption at 30V: Less than 40 mA
- Maximum washer output current: 1A
- Reverse polarity protection: Yes
- Operating temperature: -25°C to +50°C
- Storage temperature: -30°C to +80°C
Note: The internal motor protection devices do not replace an external fuse for the power supply cable. The fuse rating and cable cross-section must be selected according to the total electrical load and installation instructions.
Connections for five wiper motors
The relay box is equipped with five four-pin motor connectors. These connections are used for the motor power supply, wiping speeds and park switch circuit.
According to the wiring diagram, the following connection codes are used:
- FAST: High wiping speed, motor code 53b.
- SLOW: Low wiping speed, motor code 53.
- -M: Negative/ground connection according to the wiring diagram.
- PARK: Connection for the park switch circuit.
The park contacts of the connected motors must be suitable for the electronic control system. According to the manual, the system requires a park switch with an open contact in the park position.
The exact wire colours and additional motor connections must be checked against the wiring diagram of the relevant wiper motor.
Important: Do not connect wiper motors based solely on wire colour. Always refer to the corresponding technical documentation.
CAN bus connection and windscreen washer output
The SRM5P has two eight-pin CAN bus connections for communication with the control panel.
In a suitable installation, a second control panel can be connected, allowing the wipers to be operated from multiple helm positions.
The relay box provides the following connections:
- Motor connectors: 5 four-pin connections.
- Power supply connections: 2 connection terminals with 9.5 mm Faston terminals.
- Washer output: 1 connection terminal with a 6.3 mm Faston terminal.
- CAN bus: 2 eight-pin connections.
The washer output can be used to control a suitable washer pump or compatible solenoid valve with a maximum output current of 1A.
The complete CT2N control system is supplied as standard with a 5-metre CAN bus connecting cable. When replacing only the relay box, check that the existing cable is still suitable and undamaged.
Installation and dimensions
The SRM5P has a grey ABS housing and is installed separately from the dashboard control panel.
According to the technical manual, the relay box has the following external dimensions:
- Length: 191 mm
- Width: 109 mm
- Height: 40 mm
Install the relay box in a protected location with sufficient space for the electrical connections. Allow adequate space for the cables and ensure that the module remains accessible for inspection and maintenance.
The wiring must be protected against moisture, sharp edges, vibrations and mechanical damage.
Note: Before installation, check the exact mounting points of the supplied relay box. The external dimensions of the control panel differ from those of the relay box.
Compatibility and replacement
The SRM5P is designed for the CT2N wiper control system with five motors and is combined with a CP4P5 control panel.
According to the product specifications, the system can be used with suitable wiper motors from the MD1, MD2, HD1 and HD2 series.
When replacing an existing relay box, the following components and specifications must be checked:
- The part number and type of the existing module.
- The compatibility of the installed control panel.
- The supply voltage and current consumption of the motors.
- The connections for low and high wiping speeds.
- The operation of the park switches.
- The existing motor connectors and CAN bus cable.
Within the CT2N series, separate relay boxes are also available for two wipers (SRM2P), three wipers (SRM3P) and four wipers (SRM4P). Each version has a different number of motor outputs and must be combined with a compatible control panel.
Important: A relay box for five motors from another control system series is not automatically interchangeable. Therefore, check the exact system version before ordering a replacement part.
Troubleshooting the wiper system
If one or more wipers stop working, the relay box is not necessarily defective. The problem may also be caused by the power supply, motors, park switches or CAN bus connection.
The connected control panel can indicate various faults:
- Flashing LED for a wiper: Possible motor fault, defective park signal, incorrect connection or activated motor protection.
- Sequential LED indication: Possible communication fault between the control panel and relay box.
- Incorrect park position: Check the park switch and associated motor wiring.
- Synchronisation problems: Check the operation of the motors and their park signals.
In the event of a communication fault, first inspect the CAN bus cable for damage and poor connector connections.
If motors were connected while the relay box was already powered, the manual describes a reset procedure in which the power supply is switched off and reconnected after two minutes.
Important: Disconnect the power supply before connecting or disconnecting connectors. Connect all motors first and only then switch on the power supply.
Downloads
CT2N wiper control manual – Dutch (PDF) – Dutch-language manual containing the wiring diagram for the SRM5P relay box, technical specifications, CAN bus connections, mounting dimensions, control functions and troubleshooting information.





2 reviews for CT2N SRM5P relay box 12/24V for 5 wipers